Free tool

1RM Calculator

Estimate your one-rep max from a hard set of 2 to 6 reps, then get the weights to use at every training percentage, without testing a true max.

Units
Reps left in the tank

If you stopped short of failure, the calculator adds the reps you had left. For the best estimate, use a near-max set of 2–6 reps.

Estimated one-rep max
–
–
– Epley
– Brzycki
Training weights

An estimate based on your set, not a guaranteed max. Accuracy drops as reps go up.

What is a one-rep max?

Your one-rep max (1RM) is the heaviest weight you can lift for a single rep with good technique. Many programs prescribe loads as a percentage of it, for example 4 sets at 75%.

Testing a true max is tiring and carries more risk, especially if you don’t practise heavy singles. Estimating it from a hard set of a few reps gets you close enough to set your training weights.

The formulas

The calculator uses two of the most widely used estimation equations and shows their average as your estimated 1RM.

Epley: 1RM = weight × (1 + reps ÷ 30)
Brzycki: 1RM = weight × 36 ÷ (37 − reps)
Estimated 1RM = average of the two

At low reps, the two formulas give almost the same answer. As reps climb they drift apart, which is one reason heavier, lower-rep sets give a more reliable estimate.

Worked example

100 kg for 5 reps: Epley gives 100 × (1 + 5/30) = 116.7 kg and Brzycki gives 100 × 36/32 = 112.5 kg, for an estimated 1RM of about 114.6 kg.

How to use the calculator

1. Pick a recent hard set. Use a set of 2–6 reps taken to, or very close to, failure.

2. Enter the weight and the exact reps. Count only reps with good technique.

3. Add the reps you had left. If you got 3 reps but had 1 more in the tank, choose 1 and the calculator counts it as 4.

4. Use the training weights. Read off the load for the percentage your program asks for.

Sets of more than 10 reps produce increasingly unreliable 1RM estimates and should generally be avoided for this purpose.

Training percentages

The table in the calculator turns your estimate into training loads. The rep column shows roughly how many reps most people can manage at each percentage, worked back from the Epley formula. Treat it as a starting point: some people can do more reps at a given percentage, especially on lower-body lifts.

FAQ

How accurate is a 1RM calculator?

For a near-max set of 2–6 reps, it is usually close, but it is still an estimate. Experience, the exercise, and how close to failure you really went all affect the result.

Which formula is best?

No single formula is best for everyone. Epley and Brzycki agree closely at low reps, which is why the calculator averages them and asks for a low-rep set.

Do I need to test my real 1RM?

Not unless you compete in powerlifting or simply want to. For setting training loads, a good estimate is enough and far less fatiguing.

How often should I recalculate it?

Whenever your working weights have clearly gone up, for example at the end of a training block.

Does it work for any exercise?

It works best for compound barbell lifts like the squat, bench press, and deadlift. For machines, isolation exercises, and bodyweight movements, the estimate is rougher.

References

1. Epley B. Poundage Chart. Boyd Epley Workout. Lincoln, NE; 1985.

2. Brzycki M. Strength testing: predicting a one-rep max from reps-to-fatigue. Journal of Physical Education, Recreation & Dance. 1993;64(1):88–90.

Put your numbers to work

Find a program built around percentages, progression, and good technique.

Take the program quiz →